2013 Audi A6 Oil Type & Capacity
The 2013 Audi A6 oil type depends on the engine: the 2.0L takes 5W-40 (4.9 quarts qt with filter); the 3.0L takes 5W-40 (7.2 quarts qt with filter); the Premium takes 5W-40 (4.9 quarts qt with filter); the Premium Plus takes 5W-40 (4.9 quarts qt with filter); the Prestige Quattro takes 5W-40 (7.2 quarts qt with filter), per the factory service manual.
Factory-spec answer
It depends on the engine:
- 2.0L: 5W-40, 4.9 quarts with filter
- 2.0L: 5W-40, 4.9 quarts with filter
- 3.0L: 5W-40, 7.2 quarts with filter
- 3.0L: 5W-40, 7.2 quarts with filter
- Premium: 5W-40, 4.9 quarts with filter
- Premium Plus: 5W-40, 4.9 quarts with filter
- Prestige Quattro: 5W-40, 7.2 quarts with filter
Oil capacity by engine
| Engine | Oil Type (viscosity) | Capacity w/ Filter | Capacity w/o Filter | Notes |
|---|---|---|---|---|
| 2.0L — Premium Plus Quattro, 2.0L Eng VIN F, 2.0L Eng | SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043. | 4.90 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| 2.0L — Premium Quattro, 2.0L Eng VIN F, 2.0L Eng | SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043. | 4.90 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| 3.0L — Premium Plus Quattro, 3.0L Eng VIN G, 3.0L Eng | SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043. | 7.20 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| 3.0L — Premium Quattro, 3.0L Eng VIN G, 3.0L Eng | SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043. | 7.20 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| Premium — 2.0L Eng | SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043. | 4.90 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| Premium Plus — 2.0L Eng | SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043. | 4.90 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| Prestige Quattro — 3.0L Eng | SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043. | 7.20 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
📦 DIY Oil Change Kit Builder
Complete Oil Change Bundle for 2013 Audi A6
Everything you need delivered in one order. Pre-matched to your factory spec (5W-40, 4.9 quarts).
Preferred Oil Brand:
Mobil 1 5W-40 Full Synthetic OilExact Spec
5-Quart Jug (4.9 quarts needed)
$27.97Item Link ↗
2013 Audi A6 Premium Synthetic Oil FilterExact Fit
OEM-fitment high-efficiency synthetic filter media (2.0L)
$11.99Item Link ↗
Oil Drain Plug Crush Washer Gaskets (5-Pack)Recommended
Direct-fit replacement seal — prevents oil leaks after tightening
$6.99Item Link ↗
15-Quart Low-Profile Drain Pan with Pour SpoutTool
Catch-all basin with anti-splash lip & secure transport cap
$18.99Item Link ↗
RhinoRamps 12,000 lb Drive-Up Vehicle RampsTool
Safe driveway clearance for quick vehicle underbody access
$49.99Item Link ↗
Heavy-Duty Black Nitrile Gloves (Box of 100)PPE
6-mil commercial-grade chemical & oil resistant mechanics gloves
$14.99Item Link ↗
Multi-Angle Spill-Proof Oil Funnel SetTool
Wide-mouth funnel with flexible neck to eliminate engine bay spills
$8.99Item Link ↗
Scott Blue Shop Towels (6-Pack)Supplies
Ultra-absorbent lint-free automotive towels for clean-up
$12.99Item Link ↗
Selected Items: 3 items
$46.95 est. total
As an Amazon Associate we earn from qualifying purchases. Prices shown are real-time retail estimates.
Buy the right oil & filter for your A6
🛒 Buy 5W-40 Full Synthetic Oil (4.9 quarts needed) on AmazonPopular Full Synthetic Brands (5W-40):
As an Amazon Associate we earn from qualifying purchases made through these links.
More factory specs & repair guides for your A6
🛞 2013 Audi A6 Tire Size & Pressure →🌧️ 2013 Audi A6 Wiper Blade Sizes →💡 2013 Audi A6 Light Bulb Sizes →📖 2013 Audi A6 Factory Service Manual →All fluid capacities (transmission, coolant, brakes)Powered by factory manual data from our partner network AllOEMManuals.com.
Coolant capacity
10.5 quarts (9.93 L). Part No. G 012 A8G.
Frequently asked questions
What type of oil does a 2013 Audi A6 take?
It depends on the engine: 2.0L uses 5W-40; 3.0L uses 5W-40; Premium uses 5W-40; Premium Plus uses 5W-40; Prestige Quattro uses 5W-40.
What is the oil capacity of a 2013 Audi A6?
Oil capacity depends on the engine: 2.0L holds 4.9 quarts with filter; 3.0L holds 7.2 quarts with filter; Premium holds 4.9 quarts with filter; Premium Plus holds 4.9 quarts with filter; Prestige Quattro holds 7.2 quarts with filter.
How often should I change the oil in my 2013 Audi A6?
Most 2013 Audi A6 owners follow a 5,000–7,500 mile interval with conventional oil, or up to 10,000 miles with full synthetic. Always check the oil life monitor if equipped, and consult your owner's manual — Audi recommends intervals based on driving conditions, not just mileage.
Can I use synthetic oil in my 2013 Audi A6?
Yes. 5W-40 is widely available as a full synthetic, and synthetic is safe (often recommended) for the 2013 Audi A6. What matters most is matching the factory viscosity and specification, then changing the oil and filter on schedule.
Other Audi A6 years
2018 A62017 A62016 A62015 A62014 A62012 A62011 A62010 A62009 A62008 A62007 A62006 A62005 A62004 A62003 A62002 A62001 A62000 A61999 A61998 A61997 A61996 A61995 A6
Other Audi models
100200400050008090A3A3 QuattroA3 Sportback e-tronA4A4 allroadA4 QuattroA5A5 QuattroA5 SportbackA6 allroadA6 QuattroA7A7 e QuattroA7 QuattroA8A8 e QuattroA8 QuattroallroadCabrioletCoupeCoupe QuattroQ3Q3 QuattroQ5Q5 eQ5 SportbackQ7Q8QuattroR8RS 3RS 4RS 5RS 5 SportbackRS 6RS 6 AvantRS 7RS 7 SportbackRS Q8S3S4S5S5 SportbackS6S7S8SQ5SQ5 SportbackSQ7SQ8TTTT QuattroTTSV8 Quattro