2009 Audi TT Oil Type & Capacity

The 2009 Audi TT oil type depends on the engine: the Base, 2D Convertible, BPY, Automatic DCT takes 5W-40 (4.8 quarts with filter); the Base, 2D Convertible, BPY, Standard takes 5W-40 (4.8 quarts with filter); the Base, 2D Convertible, CCTA takes 5W-40 (4.8 quarts with filter); the Base, 2D Coupe, BPY, Automatic DCT takes 5W-40 (4.8 quarts with filter); the Base, 2D Coupe, BPY, Standard takes 5W-40 (4.8 quarts with filter); the Base, 2D Coupe, CCTA takes 5W-40 (4.8 quarts with filter); the Quattro, 2D Convertible, 2.0 F takes 5W-40 (4.8 quarts with filter); the Quattro, 2D Convertible, 3.2 D, Automatic DCT takes 5W-40 (5.8 quarts with filter); the Quattro, 2D Convertible, 3.2 D, Standard takes 5W-40 (5.8 quarts with filter); the Quattro, 2D Coupe, 2.0 F takes 5W-40 (4.8 quarts with filter); the Quattro, 2D Coupe, 3.2 D, Automatic DCT takes 5W-40 (5.8 quarts with filter); the Quattro, 2D Coupe, 3.2 D, Standard takes 5W-40 (5.8 quarts with filter); the S Quattro, 2D Convertible takes 5W-40 (4.8 quarts with filter); the S Quattro, 2D Coupe takes 5W-40 (4.8 quarts with filter), per the factory service manual.

Factory-spec answer

It depends on the engine:

Oil capacity by engine

EngineOil Type (viscosity)Capacity w/ FilterCapacity w/o FilterNotes
Base, 2D Convertible, BPY, Automatic DCT — Base,Quattro,2.0L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).4.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Base, 2D Convertible, BPY, Standard — Base,Quattro,2.0L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).4.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Base, 2D Convertible, CCTA — Base,Quattro,2.0L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).4.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Base, 2D Coupe, BPY, Automatic DCT — Base,Quattro,2.0L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).4.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Base, 2D Coupe, BPY, Standard — Base,Quattro,2.0L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).4.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Base, 2D Coupe, CCTA — Base,Quattro,2.0L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).4.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Quattro, 2D Convertible, 2.0 F — Base,Quattro,2.0L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).4.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Quattro, 2D Convertible, 3.2 D, Automatic DCT — Quattro,3.2L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).5.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Quattro, 2D Convertible, 3.2 D, Standard — Quattro,3.2L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).5.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Quattro, 2D Coupe, 2.0 F — Base,Quattro,2.0L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).4.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Quattro, 2D Coupe, 3.2 D, Automatic DCT — Quattro,3.2L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).5.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Quattro, 2D Coupe, 3.2 D, Standard — Quattro,3.2L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).5.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
S Quattro, 2D Convertible — S Quattro,2.0L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).4.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
S Quattro, 2D Coupe — S Quattro,2.0L EngSAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).4.80 QTS.Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.

Buy the right oil

Buy 5W-40 motor oil on Amazon2009 Audi TT oil filter on Amazon

As an Amazon Associate we earn from qualifying purchases made through these links.

More specs & repair guides for your TT

2009 Audi TT factory service manualAll fluid capacities (transmission, coolant, brakes)

Powered by factory manual data from our partner site AllOEMManuals.com.

Coolant capacity

9.5 quarts (8.99 L) — Coolant additive G12++. The cooling system has been filled at the factory with permanent coolant which DOES NOT need to be changed. Even in an emergency, if the coolant additive G12++. G12+ or G12 is not available, do not use a different additive. Use plain water instead until you get the correct additive and can restore the correct ratio. This should be done as soon as possible.

Frequently asked questions

What type of oil does a 2009 Audi TT take?

It depends on the engine: Base, 2D Convertible, BPY, Automatic DCT uses 5W-40; Base, 2D Convertible, BPY, Standard uses 5W-40; Base, 2D Convertible, CCTA uses 5W-40; Base, 2D Coupe, BPY, Automatic DCT uses 5W-40; Base, 2D Coupe, BPY, Standard uses 5W-40; Base, 2D Coupe, CCTA uses 5W-40; Quattro, 2D Convertible, 2.0 F uses 5W-40; Quattro, 2D Convertible, 3.2 D, Automatic DCT uses 5W-40; Quattro, 2D Convertible, 3.2 D, Standard uses 5W-40; Quattro, 2D Coupe, 2.0 F uses 5W-40; Quattro, 2D Coupe, 3.2 D, Automatic DCT uses 5W-40; Quattro, 2D Coupe, 3.2 D, Standard uses 5W-40; S Quattro, 2D Convertible uses 5W-40; S Quattro, 2D Coupe uses 5W-40.

How much oil does a 2009 Audi TT take?

Capacity depends on the engine: Base, 2D Convertible, BPY, Automatic DCT holds 4.8 quarts with filter; Base, 2D Convertible, BPY, Standard holds 4.8 quarts with filter; Base, 2D Convertible, CCTA holds 4.8 quarts with filter; Base, 2D Coupe, BPY, Automatic DCT holds 4.8 quarts with filter; Base, 2D Coupe, BPY, Standard holds 4.8 quarts with filter; Base, 2D Coupe, CCTA holds 4.8 quarts with filter; Quattro, 2D Convertible, 2.0 F holds 4.8 quarts with filter; Quattro, 2D Convertible, 3.2 D, Automatic DCT holds 5.8 quarts with filter; Quattro, 2D Convertible, 3.2 D, Standard holds 5.8 quarts with filter; Quattro, 2D Coupe, 2.0 F holds 4.8 quarts with filter; Quattro, 2D Coupe, 3.2 D, Automatic DCT holds 5.8 quarts with filter; Quattro, 2D Coupe, 3.2 D, Standard holds 5.8 quarts with filter; S Quattro, 2D Convertible holds 4.8 quarts with filter; S Quattro, 2D Coupe holds 4.8 quarts with filter.

Can I use synthetic oil in my 2009 Audi TT?

Yes. 5W-40 is widely available as a full synthetic, and synthetic is safe (often recommended) for the 2009 Audi TT. What matters most is matching the factory viscosity and specification, then changing the oil and filter on schedule.

Other Audi TT years

2013 TT2012 TT2011 TT2010 TT2008 TT2006 TT2005 TT2004 TT2003 TT2002 TT2001 TT2000 TT

Other Audi models

100200400050008090A3A3 QuattroA3 Sportback e-tronA4A4 allroadA4 QuattroA5A5 QuattroA5 SportbackA6A6 allroadA6 QuattroA7A7 e QuattroA7 QuattroA8A8 e QuattroA8 QuattroallroadCabrioletCoupeCoupe QuattroQ3Q3 QuattroQ5Q5 eQ5 SportbackQ7Q8QuattroR8RS 3RS 4RS 5RS 5 SportbackRS 6RS 6 AvantRS 7RS 7 SportbackRS Q8S3S4S5S5 SportbackS6S7S8SQ5SQ5 SportbackSQ7SQ8TT QuattroTTSV8 Quattro