2014 Audi A6 Quattro Oil Type & Capacity
The 2014 Audi A6 Quattro oil type depends on the engine: the 2.0L takes 5W-40 (4.9 quarts with filter); the 2.0L takes 5W-40 (4.9 quarts with filter); the 3.0L takes 5W-40 (7.2 quarts with filter); the 3.0L takes 5W-40 (7.2 quarts with filter); the 3.0L takes 5W-40 (7.2 quarts with filter); the Prestige, Eng CD CGXB takes 5W-40 (7.2 quarts with filter); the Prestige, Eng CD CTUA takes 5W-40 (7.2 quarts with filter); the TDI Premium Plus takes 5W-40 (6.8 quarts with filter); the TDI Prestige takes 5W-40 (6.8 quarts with filter), per the factory service manual.
Factory-spec answer
It depends on the engine:
- 2.0L: 5W-40, 4.9 quarts with filter
- 2.0L: 5W-40, 4.9 quarts with filter
- 3.0L: 5W-40, 7.2 quarts with filter
- 3.0L: 5W-40, 7.2 quarts with filter
- 3.0L: 5W-40, 7.2 quarts with filter
- Prestige, Eng CD CGXB: 5W-40, 7.2 quarts with filter
- Prestige, Eng CD CTUA: 5W-40, 7.2 quarts with filter
- TDI Premium Plus: 5W-40, 6.8 quarts with filter
- TDI Prestige: 5W-40, 6.8 quarts with filter
Oil capacity by engine
| Engine | Oil Type (viscosity) | Capacity w/ Filter | Capacity w/o Filter | Notes |
|---|---|---|---|---|
| 2.0L — 2.0L Eng | SAE 5W-40 or 5W-30. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043 | 4.90 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| 2.0L — 2.0L Eng | SAE 5W-40 or 5W-30. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043 | 4.90 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| 3.0L — 3.0L Eng,Gas | SAE 5W-40 or 5W-30. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043 | 7.20 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| 3.0L — 3.0L Eng,Gas | SAE 5W-40 or 5W-30. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043 | 7.20 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| 3.0L — 3.0L Eng,Gas | SAE 5W-40 or 5W-30. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043 | 7.20 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| Prestige, Eng CD CGXB — 3.0L Eng,Gas | SAE 5W-40 or 5W-30. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043 | 7.20 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| Prestige, Eng CD CTUA — 3.0L Eng,Gas | SAE 5W-40 or 5W-30. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043 | 7.20 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| TDI Premium Plus — 3.0L Eng,Diesel | SAE 5W-40 or 5W-30. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 507 00. See TSB No. 2010043 | 6.80 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
| TDI Prestige — 3.0L Eng,Diesel | SAE 5W-40 or 5W-30. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 507 00. See TSB No. 2010043 | 6.80 QTS. | — | Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill. |
Buy the right oil
Buy 5W-40 motor oil on Amazon2014 Audi A6 Quattro oil filter on AmazonAs an Amazon Associate we earn from qualifying purchases made through these links.
More specs & repair guides for your A6 Quattro
2014 Audi A6 Quattro factory service manualAll fluid capacities (transmission, coolant, brakes)Powered by factory manual data from our partner site AllOEMManuals.com.
Coolant capacity
10.5 quarts (9.93 L) — G13 TL-VW774J. Dilute with distilled water.
Frequently asked questions
What type of oil does a 2014 Audi A6 Quattro take?
It depends on the engine: 2.0L uses 5W-40; 2.0L uses 5W-40; 3.0L uses 5W-40; 3.0L uses 5W-40; 3.0L uses 5W-40; Prestige, Eng CD CGXB uses 5W-40; Prestige, Eng CD CTUA uses 5W-40; TDI Premium Plus uses 5W-40; TDI Prestige uses 5W-40.
How much oil does a 2014 Audi A6 Quattro take?
Capacity depends on the engine: 2.0L holds 4.9 quarts with filter; 2.0L holds 4.9 quarts with filter; 3.0L holds 7.2 quarts with filter; 3.0L holds 7.2 quarts with filter; 3.0L holds 7.2 quarts with filter; Prestige, Eng CD CGXB holds 7.2 quarts with filter; Prestige, Eng CD CTUA holds 7.2 quarts with filter; TDI Premium Plus holds 6.8 quarts with filter; TDI Prestige holds 6.8 quarts with filter.
Can I use synthetic oil in my 2014 Audi A6 Quattro?
Yes. 5W-40 is widely available as a full synthetic, and synthetic is safe (often recommended) for the 2014 Audi A6 Quattro. What matters most is matching the factory viscosity and specification, then changing the oil and filter on schedule.
Other Audi A6 Quattro years
2025 A6 Quattro2024 A6 Quattro2023 A6 Quattro2022 A6 Quattro2021 A6 Quattro2020 A6 Quattro2019 A6 Quattro2018 A6 Quattro2017 A6 Quattro2016 A6 Quattro2015 A6 Quattro
Other Audi models
100200400050008090A3A3 QuattroA3 Sportback e-tronA4A4 allroadA4 QuattroA5A5 QuattroA5 SportbackA6A6 allroadA7A7 e QuattroA7 QuattroA8A8 e QuattroA8 QuattroallroadCabrioletCoupeCoupe QuattroQ3Q3 QuattroQ5Q5 eQ5 SportbackQ7Q8QuattroR8RS 3RS 4RS 5RS 5 SportbackRS 6RS 6 AvantRS 7RS 7 SportbackRS Q8S3S4S5S5 SportbackS6S7S8SQ5SQ5 SportbackSQ7SQ8TTTT QuattroTTSV8 Quattro