2013 Audi A5 Oil Type & Capacity: 5W-40 (4.9 quarts)

The 2013 Audi A5 takes 5W-40 motor oil — 4.9 quarts with a filter change, per the factory service manual.

Factory-spec answer

5W-40 — 4.9 quarts with filter

🛒 Buy 5W-40 Full Synthetic Oil (4.9 quarts needed) →🔧 A5 Oil Filter →

Oil capacity by engine

Engine	Oil Type (viscosity)	Capacity w/ Filter	Capacity w/o Filter	Notes
Premium Plus Quattro, 2D Convertible, Eng CD CAEB	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Plus Quattro, 2D Convertible, Eng CD CPMA	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Plus Quattro, 2D Coupe, Eng CD CAEB, Automatic Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Plus Quattro, 2D Coupe, Eng CD CAEB, Standard Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Plus Quattro, 2D Coupe, Eng CD CPMA, Automatic Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Plus Quattro, 2D Coupe, Eng CD CPMA, Standard Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Plus, Eng CD CAEB	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Plus, Eng CD CPMA	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Quattro, 2D Convertible, Eng CD CAEB	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Quattro, 2D Convertible, Eng CD CPMA	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Quattro, 2D Coupe, Eng CD CAEB, Automatic Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Quattro, 2D Coupe, Eng CD CAEB, Standard Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Quattro, 2D Coupe, Eng CD CPMA, Automatic Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium Quattro, 2D Coupe, Eng CD CPMA, Standard Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium, Eng CD CAEB	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Premium, Eng CD CPMA	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Prestige Quattro, 2D Convertible, Eng CD CAEB	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Prestige Quattro, 2D Convertible, Eng CD CPMA	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Prestige Quattro, 2D Coupe, Eng CD CAEB, Automatic Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Prestige Quattro, 2D Coupe, Eng CD CAEB, Standard Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Prestige Quattro, 2D Coupe, Eng CD CPMA, Automatic Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Prestige Quattro, 2D Coupe, Eng CD CPMA, Standard Trans	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Prestige, Eng CD CAEB	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.
Prestige, Eng CD CPMA	SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.	4.90 QTS.	—	Use only a high-quality engine oil that expressly complies with the AUDI oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any AUDI Limited Warranty. DO NOT mix lubricants or other additives into the engine oil. Doing so can cause engine damage. Damaged caused by these kinds of additives are not covered by any AUDI Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. DO NOT overfill.

📦 DIY Oil Change Kit Builder

Complete Oil Change Bundle for 2013 Audi A5

Everything you need delivered in one order. Pre-matched to your factory spec (5W-40, 4.9 quarts).

Preferred Oil Brand:

Mobil 1 5W-40 Full Synthetic OilExact Spec

5-Quart Jug (4.9 quarts needed)

$27.97Item Link ↗

2013 Audi A5 Premium Synthetic Oil FilterExact Fit

OEM-fitment high-efficiency synthetic filter media (Premium Plus Quattro, 2D Convertible, Eng CD CAEB)

$11.99Item Link ↗

Oil Drain Plug Crush Washer Gaskets (5-Pack)Recommended

Direct-fit replacement seal — prevents oil leaks after tightening

$6.99Item Link ↗

15-Quart Low-Profile Drain Pan with Pour SpoutTool

Catch-all basin with anti-splash lip & secure transport cap

$18.99Item Link ↗

RhinoRamps 12,000 lb Drive-Up Vehicle RampsTool

Safe driveway clearance for quick vehicle underbody access

$49.99Item Link ↗

Heavy-Duty Black Nitrile Gloves (Box of 100)PPE

6-mil commercial-grade chemical & oil resistant mechanics gloves

$14.99Item Link ↗

Multi-Angle Spill-Proof Oil Funnel SetTool

Wide-mouth funnel with flexible neck to eliminate engine bay spills

$8.99Item Link ↗

Scott Blue Shop Towels (6-Pack)Supplies

Ultra-absorbent lint-free automotive towels for clean-up

$12.99Item Link ↗

Selected Items: 3 items

$46.95 est. total

🛒Buy Complete DIY Kit on Amazon (~$46.95) →

As an Amazon Associate we earn from qualifying purchases. Prices shown are real-time retail estimates.

Buy the right oil & filter for your A5

🛒 Buy 5W-40 Full Synthetic Oil (4.9 quarts needed) on Amazon

Popular Full Synthetic Brands (5W-40):

Mobil 1 →Valvoline Advanced →Pennzoil Platinum →Castrol EDGE →

🔧 2013 Audi A5 Oil Filter on Amazon Drain plug crush washer on Amazon

+ 15 Qt Drain Pan + Shop Towels (6 pack)+ Nitrile Gloves (100 pk)

As an Amazon Associate we earn from qualifying purchases made through these links.

More factory specs & repair guides for your A5

🛞 2013 Audi A5 Tire Size & Pressure →🌧️ 2013 Audi A5 Wiper Blade Sizes →💡 2013 Audi A5 Light Bulb Sizes →📖 2013 Audi A5 Factory Service Manual →All fluid capacities (transmission, coolant, brakes)

Coolant capacity

N/A (N/A). Part No. G 012 A8G. Fluid Capacity is between: 7.4 - 9.5 qts.

Frequently asked questions

What type of oil does a 2013 Audi A5 take?

The 2013 Audi A5 takes 5W-40 motor oil (SAE 5W-40. Petroleum or synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 2010043.), per the factory service manual.

What is the oil capacity of a 2013 Audi A5?

The 2013 Audi A5 oil capacity is 4.9 quarts with a filter change.

How often should I change the oil in my 2013 Audi A5?

Most 2013 Audi A5 owners follow a 5,000–7,500 mile interval with conventional oil, or up to 10,000 miles with full synthetic. Always check the oil life monitor if equipped, and consult your owner's manual — Audi recommends intervals based on driving conditions, not just mileage.

Can I use synthetic oil in my 2013 Audi A5?

Yes. 5W-40 is widely available as a full synthetic, and synthetic is safe (often recommended) for the 2013 Audi A5. What matters most is matching the factory viscosity and specification, then changing the oil and filter on schedule.

Other Audi A5 years

2014 A5 2012 A5 2011 A5 2010 A5 2009 A5 2008 A5