2007 Volkswagen New Beetle Oil Type & Capacity
The 2007 Volkswagen New Beetle takes 5W-40 motor oil — 6.3 quarts with a filter change, per the factory service manual.
Factory-spec answer
5W-40 — 6.3 quarts with filter
Oil capacity by engine
| Engine | Oil Type (viscosity) | Capacity w/ Filter | Capacity w/o Filter | Notes |
|---|---|---|---|---|
| 2D Convertible, 2.5 F, Automatic | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Convertible, 2.5 F, Standard | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Convertible, 2.5 G, Automatic | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Convertible, 2.5 G, Standard | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Convertible, 2.5 W, Automatic | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Convertible, 2.5 W, Standard | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Hatchback, 2.5 F, Automatic | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Hatchback, 2.5 F, Standard | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Hatchback, 2.5 G, Automatic | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Hatchback, 2.5 G, Standard | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Hatchback, 2.5 W, Automatic | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
| 2D Hatchback, 2.5 W, Standard | SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855). | 6.30 QTS. | — | Use only a high-quality engine oil that expressly complies with the Volkswagen oil quality standard specified for your vehicle's engine. Using any other oil can cause serious engine damage that will not be covered by any Volkswagen Limited Warranty. DO NOT mix any lubricants or other additives into the engine oil. Doing so can cause engine damage. Damage caused by these kinds of additives are not covered by any Volkswagen Limited Warranty. Overfilling engine oil can cause misfire DTC's to be stored in the Engine Control Module (ECM) -J220-. To prevent overfilling, add approx. 0.5 less than capacity, start engine and let it run until engine operating temperature is approx. 140Deg. F (60Deg. C), turn OFF ignition, wait approx. 3 min., check dipstick, then fill to MAX. TURBO ENGINES ONLY: After changing oil and filter, start and run engine at idle until oil pressure light goes out. DO NOT rev engine, as this could cause damage/failure of the turbocharger. Quantities are approximate. |
Buy the right oil
Buy 5W-40 motor oil on Amazon2007 Volkswagen New Beetle oil filter on AmazonAs an Amazon Associate we earn from qualifying purchases made through these links.
More specs & repair guides for your New Beetle
2007 Volkswagen New Beetle factory service manualAll fluid capacities (transmission, coolant, brakes)Powered by factory manual data from our partner site AllOEMManuals.com.
Coolant capacity
10.0 quarts (9.46 L) — Phosphate-free Coolant G 012 A8F A4
Frequently asked questions
What type of oil does a 2007 Volkswagen New Beetle take?
The 2007 Volkswagen New Beetle takes 5W-40 motor oil (SAE 5W-40 or SAE 5W-30. Synthetic based oils. Engine oil must conform to the exact specification in VW publication VW 502 00. See TSB No. 17 09-07 (2012855).), per the factory service manual.
How much oil does a 2007 Volkswagen New Beetle take?
The 2007 Volkswagen New Beetle holds 6.3 quarts with a filter change.
Can I use synthetic oil in my 2007 Volkswagen New Beetle?
Yes. 5W-40 is widely available as a full synthetic, and synthetic is safe (often recommended) for the 2007 Volkswagen New Beetle. What matters most is matching the factory viscosity and specification, then changing the oil and filter on schedule.
Other Volkswagen New Beetle years
2010 New Beetle2009 New Beetle2008 New Beetle2006 New Beetle2005 New Beetle2004 New Beetle2003 New Beetle2002 New Beetle2001 New Beetle2000 New Beetle1999 New Beetle1998 New Beetle